Prepared Society Forum banner

7081 - 7100 of 7107 Posts

·
WELL SEASONED
Joined
·
768 Posts
23383
 

·
WELL SEASONED
Joined
·
768 Posts
23384
 

·
WELL SEASONED
Joined
·
768 Posts
23385
 

·
WELL SEASONED
Joined
·
768 Posts
23386
23387
23388
 

·
WELL SEASONED
Joined
·
768 Posts
As soon as the metal lathe project is finished I will start on the milling machine project. Photos are of geared feed motor for the X axis of the milling machine table.
 

·
WELL SEASONED
Joined
·
768 Posts
Fruit trees are all trimmed up and starting to bud out.
23389
 

·
WELL SEASONED
Joined
·
768 Posts
I had taken these photos last summer one is of the fall
23390
23391
equinox sun setting and the other is the summer solstice sun setting. Can you tell which one is which? If you are involved in solar energy you should know the difference.
 

·
WELL SEASONED
Joined
·
768 Posts
I just want to remind everyone again that when you buy your own piece of land out in the country you now become a sewage treatment plant operator, a water treatment plant operator, a power generation plant operator, a plumber, a electrician, a carpenter, a mechanic
23392
, a equipment operator, the list goes on and on. This is a photo of my air injection pump for my sewage treatment plant out for inspection. So you thought living in the country was a more simplistic lifestyle, HA!
 

·
WELL SEASONED
Joined
·
768 Posts
What made this hole?
23393
 

·
WELL SEASONED
Joined
·
768 Posts
Still a work in progress.
23394
23395
 

·
WELL SEASONED
Joined
·
768 Posts
I can finly put the done stamp on the metal lathe project. Improvements are, 3 phase motor, vfd inverter drive, spindle rpm display, chip drawer, add door and shelf on bottom left stand, clean and paint, fwd/rev jog switch, leveling feet, rebuild chip tray, and I can't remember what else but I started on this project last fall and I've had enough.
23396
23397
23399
23400
23401
 

·
WELL SEASONED
Joined
·
768 Posts
I go through this ever year, rebuild the mower deck. This year it was replace two bearings, weld cracks, replace one wheel, replace one belt, clean off rust and grass, paint, and sharpen blades. The simple life...right.
23403
23404
 

·
WELL SEASONED
Joined
·
768 Posts
I just bought this 10" Jet pedestal grinder from the surplus store for $125 and the standard procedure for me is to pour concrete into the base and mount adjusting feet on the bottom. I would like to have a wire wheel, fine and course grinding wheel, and green carbide wheel all set up and ready to use.
23405
23406
23407
 

·
WELL SEASONED
Joined
·
768 Posts
The circuit I built for the metal lathe.
23408
 

·
WELL SEASONED
Joined
·
768 Posts
I bought 30 pounds of grade 2 nuts, bolts, and washers today, prices are going up.
 

·
WELL SEASONED
Joined
·
768 Posts
S
23409
23410
23411
eriously folks prices are skyrocketing, 30 lbs of nuts, bolts, and washers was $50, drill bits $200, all I can say is you had better buy what you want now because a couple months from now it will only cost you more money.
 

·
WELL SEASONED
Joined
·
768 Posts
I took this photo the other day, unfortunately the end of the rainbow didn't fall on my property so no pot of gold for me.
23413
 

·
WELL SEASONED
Joined
·
768 Posts
23414
23415
23416
23417
23418
23419
 

·
WELL SEASONED
Joined
·
768 Posts
23420
 

·
WELL SEASONED
Joined
·
768 Posts
23421
 
7081 - 7100 of 7107 Posts
Top